Excellent Water Quality
| Contaminant | Detected Level | EPA MCL | Health Guideline | Status |
|---|---|---|---|---|
| Lead |
3.9
|
15 ppb | 1 ppb | Warning |
| Copper |
1370.0
|
1300 ppb | 300 ppb | Exceeded |
Water Quality Summary
Tap water quality in Walcott, North Dakota (58077) receives an overall grade of A (Excellent) with a score of 93 out of 100, based on analysis of EPA compliance data, contaminant testing, and violation history. This is 7 points above the North Dakota state average of 86. Compared to the national average (75), this area performs significantly better. The area is served by 3 water systems providing water to approximately 6,160 people, using groundwater sources. Testing has found elevated levels of Lead, Copper that warrant attention.
A score of 93/100 means the water supply in Walcott, ND meets or exceeds all EPA standards with minimal issues. Contaminant levels are well within safe limits, and the water system has maintained a strong compliance record. While no water supply is guaranteed perfect at the tap due to household plumbing, this is among the best-scoring areas in the country.
Health Information
Lead is a toxic metal that can leach from aging pipes and plumbing fixtures.
Even low levels of lead exposure can cause developmental delays in children, kidney damage, and cardiovascular effects in adults. The EPA action level is 15 ppb, but health experts recommend no safe level of lead in drinking water.
Lead enters water primarily through corrosion of lead service lines, lead solder, and brass fixtures — especially in homes built before 1986.
If lead is detected above 1 ppb, consider using a certified lead-removal filter (NSF/ANSI 53) for drinking and cooking water. Run cold water for 30 seconds before use if water has been sitting in pipes.
Copper can leach into water from copper plumbing, especially in newer homes or when water is acidic.
Short-term exposure above 1,300 ppb can cause gastrointestinal distress. Long-term exposure may cause liver or kidney damage. People with Wilson's disease are especially vulnerable.
Copper pipes, fittings, and faucets are the most common source. Corrosive (low-pH) water accelerates copper leaching.
If copper levels are elevated, flush pipes by running water for 15–30 seconds before use. Reverse osmosis and distillation systems effectively remove copper.
Common Questions
Based on EPA data, tap water in Walcott, North Dakota receives a grade of A (Excellent) with a score of 93/100. This indicates the water meets federal standards and has relatively few concerns. However, individual homes may still have localized issues such as lead from old plumbing.
ZIP code 58077 is served by 3 water systems using groundwater sources, providing water to approximately 6,160 people. Groundwater is naturally filtered through rock and soil, often requiring less treatment. However, it can be vulnerable to contamination from underground sources like naturally occurring arsenic, nitrates from agriculture, or PFAS from industrial sites.
Lead was detected at 3.9 ppb in Walcott, North Dakota. While this is below the EPA action level of 15 ppb, it exceeds the health guideline of 1 ppb recommended by health organizations. Consider a certified lead filter, especially if you have young children.
No PFAS ("forever chemicals") were detected in water systems serving Walcott, North Dakota during the most recent EPA monitoring period (UCMR5). However, not all water systems have been tested for all PFAS compounds, and new contamination can occur over time.
Water systems serving Walcott, North Dakota have received 2 violations in the last 5 years. Violations can range from paperwork issues (monitoring & reporting) to serious health-based violations where contaminant levels exceeded safe limits. Review the violation details above for specifics.
Based on detected contaminants (lead, copper), residents in Walcott, North Dakota should consider: NSF/ANSI 53 certified filter — specifically rated for lead reduction. Pitcher filters (like Brita Longlast or PUR) and under-sink systems both work. Always look for filters with NSF/ANSI certification for the specific contaminants you want to remove.