Excellent Water Quality
| Contaminant | Detected Level | EPA MCL | Health Guideline | Status |
|---|---|---|---|---|
| Lead |
1.0
|
15 ppb | 1 ppb | Passed |
| Copper |
1400.0
|
1300 ppb | 300 ppb | Exceeded |
| Compound | Level | EPA MCL | Health Guideline | Status |
|---|---|---|---|---|
| PFBA | 16.6 ppt | No standard | 500 ppt | Unregulated |
Water Quality Summary
Tap water quality in Hopkins, Minnesota (55305) receives an overall grade of A (Excellent) with a score of 98 out of 100, based on analysis of EPA compliance data, contaminant testing, and violation history. This is 10 points above the Minnesota state average of 88. Compared to the national average (75), this area performs significantly better. The area is served by Minnetonka, a groundwater system providing water to approximately 54,474 people. Testing has found elevated levels of Copper that warrant attention. PFAS testing detected 1 compound, all currently below EPA limits. The area has a clean violation record over the past 5 years — a positive indicator of consistent water quality management.
A score of 98/100 means the water supply in Hopkins, MN meets or exceeds all EPA standards with minimal issues. Contaminant levels are well within safe limits, and the water system has maintained a strong compliance record. While no water supply is guaranteed perfect at the tap due to household plumbing, this is among the best-scoring areas in the country.
Health Information
Lead is a toxic metal that can leach from aging pipes and plumbing fixtures.
Even low levels of lead exposure can cause developmental delays in children, kidney damage, and cardiovascular effects in adults. The EPA action level is 15 ppb, but health experts recommend no safe level of lead in drinking water.
Lead enters water primarily through corrosion of lead service lines, lead solder, and brass fixtures — especially in homes built before 1986.
If lead is detected above 1 ppb, consider using a certified lead-removal filter (NSF/ANSI 53) for drinking and cooking water. Run cold water for 30 seconds before use if water has been sitting in pipes.
Copper can leach into water from copper plumbing, especially in newer homes or when water is acidic.
Short-term exposure above 1,300 ppb can cause gastrointestinal distress. Long-term exposure may cause liver or kidney damage. People with Wilson's disease are especially vulnerable.
Copper pipes, fittings, and faucets are the most common source. Corrosive (low-pH) water accelerates copper leaching.
If copper levels are elevated, flush pipes by running water for 15–30 seconds before use. Reverse osmosis and distillation systems effectively remove copper.
Common Questions
Based on EPA data, tap water in Hopkins, Minnesota receives a grade of A (Excellent) with a score of 98/100. This indicates the water meets federal standards and has relatively few concerns. However, individual homes may still have localized issues such as lead from old plumbing.
ZIP code 55305 is served by 1 water system using groundwater sources, providing water to approximately 54,474 people. Groundwater is naturally filtered through rock and soil, often requiring less treatment. However, it can be vulnerable to contamination from underground sources like naturally occurring arsenic, nitrates from agriculture, or PFAS from industrial sites.
Lead levels in Hopkins, Minnesota are 1.0 ppb, which is at or below the health guideline of 1 ppb. This is a positive result, though periodic testing is still recommended.
1 PFAS compound were detected in water serving Hopkins, Minnesota, but all are currently below EPA limits. While levels are within regulatory standards, some health organizations recommend minimizing any PFAS exposure. Activated carbon or reverse osmosis filters can reduce PFAS levels.
Water systems serving Hopkins, Minnesota have zero violations in the last 5 years. This is a positive indicator of consistent regulatory compliance and water quality management.
Based on detected contaminants (PFAS, copper), residents in Hopkins, Minnesota should consider: Reverse osmosis (RO) system — most effective for PFAS, lead, and other contaminants. Always look for filters with NSF/ANSI certification for the specific contaminants you want to remove.