Poor Water Quality
| Contaminant | Detected Level | EPA MCL | Health Guideline | Status |
|---|---|---|---|---|
| Lead |
2.2
|
15 ppb | 1 ppb | Warning |
| Compound | Level | EPA MCL | Health Guideline | Status |
|---|---|---|---|---|
| PFBA | 13.8 ppt | No standard | 500 ppt | Unregulated |
| PFBA | 8.7 ppt | No standard | 500 ppt | Unregulated |
| PFPeA | 7.6 ppt | No standard | — | Unregulated |
| PFPeA | 7.6 ppt | No standard | — | Unregulated |
| PFHxA | 7.5 ppt | No standard | 400 ppt | Unregulated |
| PFBA | 7.1 ppt | No standard | 500 ppt | Unregulated |
| PFHxA | 6.7 ppt | No standard | 400 ppt | Unregulated |
| PFBS | 4.7 ppt | 2000 ppt | 100 ppt | Below limit |
Water Quality Summary
Tap water quality in Frisco, Texas (75034) receives an overall grade of D (Poor) with a score of 54 out of 100, based on analysis of EPA compliance data, contaminant testing, and violation history. This is 14 points below the Texas state average of 68. Compared to the national average (75), this area scores significantly lower. The area is served by 4 water systems providing water to approximately 286,526 people, using surface water sources. Testing has found elevated levels of Lead that warrant attention. PFAS testing detected 12 compounds, all currently below EPA limits. Over the past 5 years, water systems here have accumulated 25 violations, including 6 health-based violations.
A score of 54/100 signals poor water quality in Frisco, TX. Significant issues have been identified, which may include multiple violations, contaminant levels near or above regulatory limits, or PFAS contamination. We recommend reviewing the detailed contaminant data below, considering a certified water filter, and checking your utility's Consumer Confidence Report for the latest information.
Health Information
Lead is a toxic metal that can leach from aging pipes and plumbing fixtures.
Even low levels of lead exposure can cause developmental delays in children, kidney damage, and cardiovascular effects in adults. The EPA action level is 15 ppb, but health experts recommend no safe level of lead in drinking water.
Lead enters water primarily through corrosion of lead service lines, lead solder, and brass fixtures — especially in homes built before 1986.
If lead is detected above 1 ppb, consider using a certified lead-removal filter (NSF/ANSI 53) for drinking and cooking water. Run cold water for 30 seconds before use if water has been sitting in pipes.
Common Questions
Tap water in Frisco, Texas receives a grade of D (Poor) with a score of 54/100. This indicates significant water quality concerns based on violation history, contaminant levels, or enforcement actions. We recommend reviewing the specific contaminants detected below and considering a certified water filter.
ZIP code 75034 is served by 4 water systems using surface water sources, providing water to approximately 286,526 people. Surface water systems are more susceptible to contamination from agricultural runoff, industrial discharge, and weather events, but typically undergo more extensive treatment including filtration and disinfection.
Lead was detected at 2.2 ppb in Frisco, Texas. While this is below the EPA action level of 15 ppb, it exceeds the health guideline of 1 ppb recommended by health organizations. Consider a certified lead filter, especially if you have young children.
12 PFAS compounds were detected in water serving Frisco, Texas, but all are currently below EPA limits. While levels are within regulatory standards, some health organizations recommend minimizing any PFAS exposure. Activated carbon or reverse osmosis filters can reduce PFAS levels.
Water systems serving Frisco, Texas have received 25 violations in the last 5 years, including 6 health-based violations. Violations can range from paperwork issues (monitoring & reporting) to serious health-based violations where contaminant levels exceeded safe limits. Review the violation details above for specifics.
Based on detected contaminants (lead, PFAS), residents in Frisco, Texas should consider: Reverse osmosis (RO) system — most effective for PFAS, lead, and other contaminants. Always look for filters with NSF/ANSI certification for the specific contaminants you want to remove.